D-MAX 600 TVL Manuel d'utilisateur

User Manual HIGH SPEED DOME CAMERA 600 TVL

10 3) How to connect equipments Connect the image line of a monitor User can control maximum up to 255 cameras

11 Alarm output is tangency output of relay non-load, it can be used up to AC220/10A by connecting the load.

124) HOW TO SET PROTOCOL ① Please the power off ② Switch protocol that user wants to change on as above the cable ③ The p

135) SETTING ADDRESS OF DIP SWITCHES. RX NO DIP SWITCH (HEX) RX NODIP SWITCH (HEX) 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 ON OFF OFF OFF

14 ● OSD (ON SCREEN DISPLAY) menu control It is the function to call up the Menu ＊User can not only set Preset, Group, Tour, Swing, Trace functions

151. ID SET. This function is to set camera ID up to 16 letters on the monitor. User can choose letters that they want, if user control a joystick u

165. SHUTTER SPEED As a setting shutter speed mode, it can be distinguished a fast moving subject easily by means of shutter speed up. ※ Attention

17 9. DNR Control It can remarkably reduce noise of minimum illumination by super noise removable technique and also file size becomes smaller w

18After complete all setup, press F/N button, and then move to RETURN MENU PAGE. It is automatically saved. 12. WHITE BALANCE It prevents from

1916. DAY& NIGHT The function is used to distinguish an object clearly in the dark condition. ▶ Auto-Low : This mode is worked automatically ac

2

2020. PRESET SET & RUN PAGE It is a function to set and operate Preset, Group, Tour. User can see the screen when moves the joystick to Right/Le

21 ③ Preset Swing SET : Set Preset Swing Move next SWING page for the setting, if user presses F/F key in the state of selection of the

22⑤ Tour SET Group: User can set continual Group motion that can be put 12 Groups in 1 Tour Move to the setting page if user presses F/F key on this

2322. ALRAM CHANNEL ON/OFF - CH On/Off : Alarm Input – Each channel can be ON/OFF - Alarm Relay : It can be set On or not when ALARM OUTOUT PORT o

24※You can set ALARM setting MENU not only in CAMERA SET MENU MODE, but also a KEYBOARD in direct 24. PRIVARCY ZONE SET ☞ This function does not wo

25 24-25. AUTO TILT MOVE The PAN is turned in a 180° degree arc automatically when the angle of the camera moves down to the maximum degree, therefo

26 28-29. SHORTCUT KEY The Shortcut Key can make some of the functions to perform faster and easily. ★ How to use shortcut key ( All protocols

27 31-32. FACTORY RESET WARNING Please be careful of that all setting data of OSD MENU are reset into the first default when operates FACTORY RESET

28 1. Preset setting You can set Preset point up to 250. Preset Input.① Preset setting can be set 1 to 250 sequentially after moves the

29 ② Operation of Swing ③ End of Swing (Run Pan) (Run Tilt) 3. Group setting ① Start Group setting mode -

3 Ⅰ CAUTION --------- 4 Ⅱ INTRODUCTION OF PRODUCTS --------- 6 Ⅲ DIRECTIONS FOR USE

30 Repeat input in continual input EX). Register Group No. 1, 3, 6 as Tour ② Start / End Tour

31 1. PRESET MESSAGE CAM-001 GP:01 P002,T001,S64 CAM-001 Save Group 01CAM-001 (GROUP:01) PRESET:001 As

32 CAM-001 SET TOUR GP:01 CAM-001 TOUR&GP:01 PRESET:001CAM-001 CLEAR TOUR & GRPCAM-001 RUN SPI

33 1. You must turn off the power switch before installation of this equipment 2. Avoid installation places where it is the ultimate cold, hot, and

34When it occurred alarm state, it is not exactly presser position or different. Did you set the preset in the set mode? Check setting status of the

35 Ⅶ. DIMENSIONS Wall mount bracket Indoor Type Outdoor Type

36 Ceiling mount bracket In-ceiling mount bracket Indoor Type Outdoor Type

37 Ⅷ. ASSEMBLY DSC-30EWP Wall mount bracket ① Remove t

388 7 9 6 1 2 5 4 3 Assembly of outdoor dome with pole mount pendant DSC-20ECP Wall mount bracket Remove the M

39 Main & Sub Keyboard configuration

4 Thank you for purchasing our product. Please operate the product after being fully aware of the manual. Pease contact us if you have any queries

40 MODEL 27X Zoom □ 33X Zoom □ 37X Zoom □ Image sensor 1/4” Sony Super HAD CCD Effective pixels NTSC 768(H) X 494(V), PAL 752(H) X 582(V), H

1

2

3

4 DISTRIBUTED BY

5Caution in Use Do not disassemble the unit and put alien substances in the unit. - Disassembling the unit or putting alien substances such as a m

6 1. DESCRIPTION AND FEATURES Description This camera has been designed elegantly for buildings, department stores that need to be in harmony w

72. INSTALLATION AND CONNECTION 1) Name and function of each part (UPPER COVER) The camera’s body goes to her

82) Installation SEPARATION OF LOWER COVER (Indoor type) Loosen the bolt of the back of lower cover by a sc

9 Open the connector cover, then connect power, data, video cable and sensor The cover is opened if user loo